Posts: 3
Threads: 2
Thanks Received: 0 in 0 posts
Thanks Given: 0
Joined: Nov 2023
Reputation:
0
ZEZ: 25.25 ZEZ
[Buy]
I put a x15 cm2450 from a 2024 wreck into my 2016 peterbilt 579. It had a isx15 cm2350. I've got everything working except the brake switch, clutch switch, and Jake brake switch's. They show up and work on esa but are not communicating with the engine ecu. I'm sure it has to be a setting but I can't find anything. I've tried all the different source addresses on cummins. Currently have them set to 49 cab controller. Any guidance or does anyone have a parameter file for a similar truck vin is 1xpbd49x4gd203933
•
Posts: 202
Threads: 50
Thanks Received: 751 in 133 posts
Thanks Given: 102
Joined: Nov 2017
Reputation:
606
ZEZ: 50,266.21 ZEZ
[Buy]
11-03-2024, 01:45 PM
(This post was last modified: 11-03-2024, 01:47 PM by zyNoT.)
You need to set your multiplexing settings on engine ECM to point to the cab controller.
You can find these settings in INSITE > Features and Parameters > Multiplexing.
49 is correct, make sure that the correct CAN channels & baud rates are set.
Newer ECM's use CAN4 while older ones do not. The baud rate is also set different.
There are also parameters set in the calibration that are specific to J1939 communication.
Each calibration likely has different ones set for different chassis.
If I helped in any way, please give THANKS + REP!
Cummins INSITE 8.x/9.x+Fleet Cals, Password Resets
Cummins Calterm 5.16.0
Calterm Master Tool Ultimate v10.3
Cummins INCAL Tool v8.5
CNH 9.2 Dealer or Engineering
Wabco 13.6 Engineering
DDDL 8.20 - Levels 10/10/10
CAT ET 2024A + Perkins 2024A + FPKG/AutoGen
SR 4.12 Engineering
Bendix ACOM Pro 2024
Allison DOC 2024
JPRO 2024
Remote Tuning for all Cummins engines. PM for Quote.
•
Posts: 202
Threads: 50
Thanks Received: 751 in 133 posts
Thanks Given: 102
Joined: Nov 2017
Reputation:
606
ZEZ: 50,266.21 ZEZ
[Buy]
As I stated previously...
(11-03-2024, 01:45 PM)zyNoT Wrote: 49 is correct, make sure that the correct CAN channels & baud rates are set.
Newer ECM's use CAN4 while older ones do not. The baud rate is also set different.
There are also parameters set in the calibration that are specific to J1939 communication.
Each calibration likely has different ones set for different chassis.
So, you may need a different calibration that has the proper J1939 settings.
If I helped in any way, please give THANKS + REP!
Cummins INSITE 8.x/9.x+Fleet Cals, Password Resets
Cummins Calterm 5.16.0
Calterm Master Tool Ultimate v10.3
Cummins INCAL Tool v8.5
CNH 9.2 Dealer or Engineering
Wabco 13.6 Engineering
DDDL 8.20 - Levels 10/10/10
CAT ET 2024A + Perkins 2024A + FPKG/AutoGen
SR 4.12 Engineering
Bendix ACOM Pro 2024
Allison DOC 2024
JPRO 2024
Remote Tuning for all Cummins engines. PM for Quote.
•